Controlling thermomechanical behavior of semicrystalline hydrogenated polynorbornene through the cis- to trans-cyclopentylene ratio

Though polynorbornene synthesized by ring-opening metathesis polymerization has an intrinsically all-cis configuration of the cyclopentylene backbone rings, a fraction of these rings can be epimerized to the trans configuration during hydrogenation over suitable catalysts. By varying the method of hydrogenation, semicrystalline hydrogenated polynorbornenes (hPNs) with trans levels between 0 and 36% were obtained. With increasing trans content, the glass transition temperature, melting point, and enthalpy of melting decrease modestly. By contrast, the temperature at which the hPN crystal transitions into a rotationally disordered polymorph varies strongly with trans content, ranging from 126 °C (all-cis) to 71 °C at 27% trans; at trans contents of 34% and above, no rotationally-ordered phase is observed at any temperature. The room-temperature Young's modulus shows no dependence on trans content, while the yield stress drops by 20% at 1% trans content and slowly decreases further with additional epimerization. The temperature dependence of the Young's modulus differs for trans-containing versus all-cis polymers, while the temperature dependence of the yield stress is set by the polymorph type (rotationally ordered vs. disordered).     

基于应变梯度理论的微尺度蜂窝等效模量计算方法

本文提出了一种新的能够计及尺度效应的微纳米蜂窝等效模量的计算方法。将一种单参数应变梯度理论引入到本构方程当中,并基于能量等效原理推导了蜂窝面内等效模量地计算公式。算例分析表明,本文方法能够有效地计及尺度效应对蜂窝等效模量的影响。尺度效应与胞壁厚度和长度的值都有关,当胞壁厚度较小时,尺度效应显著,本文方法预测的模量会明显高于传统方法;而当胞壁厚度较大时,尺度效应变得微弱乃至可以忽略不计。但如果胞壁的长度/厚度比很大,则面内等效模量会趋近于0,此时是否考虑尺度效应意义不大。     

Comparative Study of Alkali-Cation-Based (Li+, Na+, K+) Electrolytes in Acetonitrile and Alkylcarbonates

The development of a suitable functional electrolyte is urgently required for fast-charging and high-voltage alkali-ion (Li, Na, K) batteries as well as next-generation hybrids supercapacitors. Many recent works focused on an optimal selection of electrolytes for alkali-ion based systems and their electrochemical performance but the understanding of the fundamental aspect that explains their different behaviour is rare. Herein, we report a comparative study of transport properties for LiPF₆, NaPF₆, KPF₆ in acetonitrile (AN) and a binary mixture of ethylene carbonate (EC), dimethyl carbonate (DMC): (EC/DMC : 1/1, weigh) through conductivities, densities and viscosities measurements in wide temperature domain. By application of the Stokes-Einstein, Nernst-Einstein, and Jones Dole equations, the effective ionic solvated radius of cation (r_eff), the ionic dissociation coefficient (α_D) and structuring Jones Dole's parameters (A, B) for salt are calculated and discussed according to solvent or cation nature as a function of temperature. From the results, we demonstrate that better mobility of potassium can be explained by the nature of the ion-ion and ion-solvent interactions due to its polarizability. In the same time, the predominance of triple ions in the case of K⁺, is a disadvantage at high concentration.     

Analytical formulas for complex permittivity of periodic composites. Estimation of gain and loss enhancement in active and passive composites

ABSTRACT

The asymptotic homogenization method is applied to complex dielectric periodic composites. An equivalence to coupled dielectric problems with real coefficients is shown. This is similar to a piezoelectric problem: an out-plane mechanical displacement and an in-plane electric potential establishing a correspondence principle. Closed-form formulas for the complex dielectric effective tensor in the case of a square array of circular inclusions embedded in a matrix are given. These formulas are written in terms of a real and symmetric matrix which facilitates the implementation of the computational scheme. We also get similar formulas for multilayered complex dielectric composites. The real closed-form formulas are advantageous for estimating gain and loss enhancement properties of active and passive composites in certain volume fraction intervals. Numerical computations are performed and the results are compared with other approaches showing the usefulness of the obtained formulas. This may be of interest in the context of metamaterials.     

Yb3+掺杂稀土钽铌酸盐的晶体场从头计算研究

Yb³⁺掺杂晶体材料是重要的激光材料,在超短脉冲激光、大功率激光等领域有重要应用前景,但长期以来很难通过实验拟合确定Yb3+晶体场参数,尤其是低对称体系,从头计算是解决此问题的重要途经.本文介绍了适合计算稀土离子掺杂晶体的从头计算DV-Xα方法和有效哈密顿量模型,用该方法计算了Yb³⁺掺杂M型和M'型钽铌酸盐的晶场参数和旋轨耦合参数,得到的能级结构和实验能很好地符合,并发现了Yb³⁺掺杂钽铌酸盐的晶场强度参数随稀土原子序数呈现规律变化.表明结合DV-Xα计算和有效哈密顿量方法是计算Yb³⁺掺杂低对称钽铌酸盐晶体场的有效途径,结果显示Yb3+掺杂钽铌酸盐晶体有望成为新型全固态激光工作物质.     

Wall shear stress modified by bubbles in a horizontal channel flow of silicone oil in the transition region

We performed laboratory experiments on bubbly channel flows using silicone oil, which has a low surface tension and clean interface to bubbles, as a test fluid to evaluate the wall shear stress modification for different regimes of bubble migration status. The channel Reynolds numbers of the flow ranged from 1000 to 5000, covering laminar, transition and turbulent flow regimes. The bubble deformation and swarms were classified as packing, film, foam, dispersed, and stretched states based on visualization of bubbles as a bulk void fraction changed. In the dispersed and film states, the wall shear stress reduced by 9% from that in the single-phase condition; by contrast, the wall shear stress increased in the stretched, packing, and foam states. We carried out statistical analysis of the time-series of the wall shear stress in the transition and turbulent-flow regimes. Variations of the PDF of the shear stress and the higher order moments in the statistic indicated that the injection of bubbles generated pseudo-turbulence in the transition regime and suppressed drag-inducing events in the turbulent regime. Bubble images and measurements of shear stress revealed a correlated wave with a time lag, for which we discuss associated to the bubble dynamics and effective viscosity of the bubble mixture in wall proximity.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064